資訊中心

金洛博客

更多>>

CTS致力于成為技術的前...

Diodes宣布推出一款智能...

ConnorWinfield溫補晶振...

CTS西迪斯低成本SMD晶體...

首頁新聞中心 IQD幾皮法會破壞你的計時準確性LFXTAL052799CUTT

IQD幾皮法會破壞你的計時準確性LFXTAL052799CUTT

來源：http://www.benpai.com.cn 作者：金洛鑫電子 2024年03月08

IQD幾皮法會破壞你的計時準確性LFXTAL052799CUTT

石英晶體因其精確的頻率而廣泛用于電子應用中。對高精度時鐘頻率的需求正在增加，特別是由于物聯網、5G和工業4.0。然而，在設計過程中的幾個錯誤就可能破壞石英晶體的整體頻率精度。

負載電容對石英晶振頻率和我的應用有什么影響？

根據應用中所需的時序精度，這可能非常重要。電路的電容決定了晶體的諧振頻率。這意味著如果電路中的電容發生變化，晶體的頻率也會發生變化。在生產過程中，晶體被校準到其特定負載電容。由此可見，如果電路中的負載電容合適，晶體將在其容差范圍內振蕩。然而，負載電容的每次變化都會改變頻率。這意味著在最壞的情況下，晶體將在其容差之外振蕩。

確定晶體頻率將偏移多少的參數是微調靈敏度。這表示如果負載電容變化1pF，頻率將變化多少ppm。調整值可在1ppm/pF至100ppm/pF之間變化，石英水晶振子具體取決于各種因素，如空白的尺寸、電極的尺寸和形狀、頻率以及負載電容。一方面，根據經驗法則，封裝尺寸越大，調整靈敏度越高。因此，1.6x1.2mm晶體的切邊將小于7.0x5.0mm貼片晶振晶體的切邊。另一方面，你需要記住負載電容越低，調整就越高。因此，如果一個晶體的負載電容為10pF，另一個晶體的負載電容為20pF，則10pF晶體的調整會更高。在下圖（圖1）中，您可以看到調整是如何隨負載電容變化的。

How a few Pico Farads can ruin your timing accuracy

圖1石英晶體的調整靈敏度取決于負載電容

因此，如果電路中的負載電容與石英晶振的額定負載不同，頻率就會偏移。此外，根據額定負載電容以及電路中負載與額定負載之間的差異，頻率變化可能會很大。在最壞的情況下，頻率會超出規格，可能無法在您的應用中工作。這就是為什么在設計過程中更詳細地觀察負載電容如此重要的原因。

IQD幾皮法會破壞你的計時準確性LFXTAL052799CUTT

How a few picoFarads can ruin your timing accuracy

Quartz crystals are widely used in electronic applications because of their accurate frequency. The demand for high precision clock frequencies is increasing, particularly owing to IoT, 5G and Industry 4.0. However, just a few mistakes during the design-in process can ruin the entire frequency accuracy of the quartz crystal.

What influence does load capacitance have on the frequency of the crystal and to my application?

Depending on the required timing accuracy in your application, this can be very important. The capacitance of the circuit defines the resonant frequency of the crystal. This means if the capacitance in the circuit changes, the frequency of the crystal changes as well. During the production process, the crystal is calibrated to its specific load capacitance. From this, it follows that with the right load capacitance in the circuit the crystal will oscillate within its tolerance. However, every change to the load capacitance will shift the frequency. This means that in the worst case scenario the crystal will oscillate outside its tolerance.

The parameter that identifies how much the frequency of the crystal will shift is the trim sensitivity. This shows by how many ppm the frequency will change, if the load capacitance is changed by 1 pF. The value of the trim can vary from 1 ppm/pF up to 100 ppm/pF and it depends on various factors, such as the size of the blank, the size and shape of the electrode, the frequency, as well as the load capacitance. On one hand, you can say as a rule of thumb, that the bigger the package size the bigger the trim sensitivity. Therefore, the trim of a 1.6 x 1.2 mm crystal will be smaller than the trim of a 7.0 x 5.0 mm crystal. On the other hand, you need to keep in mind that the lower the load capacitance, the higher the trim will be. Consequently, if you have a crystal with 10 pF load capacitance and a crystal with 20 pF load capacitance, the trim of the 10 pF crystal will be higher. In the picture below (Figure 1), you can see how the trim varies with the load capacitance.

Figure 1 Trim sensitivity of a quartz crystal depending on the load capacitance

Therefore, if the load capacitance in the circuit differs from the specified load of the crystal, the frequency will shift. In addition, depending on the specified load capacitance and the difference between the load in the circuit and the specified load, the frequency change can be dramatic. In the worst-case scenario, the frequency will be outside of the specification and it may not work in your application. This is why it is so important to look at the load capacitance in more detail during your design process.

進口貼片晶振	型號	頻率	負載電容	頻率公差	頻率穩定性
LFXTAL081314REEL	IQXC-240	37.4MHz	5.00pF	±7ppm	±15ppm
LFXTAL081316REEL	IQXC-240	38.4MHz	5.00pF	±7ppm	±15ppm
LFXTAL072539REEL	IQXC-26	24.0MHz	8.00pF	±15ppm	±15ppm
LFXTAL078691CUTT	IQXC-26	24.0MHz	20.00pF	±10ppm	±30ppm
LFXTAL081608CUTT	IQXC-26	24.0MHz	8.00pF	±10ppm	±20ppm
LFXTAL081608REEL	IQXC-26	24.0MHz	8.00pF	±10ppm	±20ppm
LFXTAL081609CUTT	IQXC-26	25.0MHz	8.00pF	±10ppm	±20ppm
LFXTAL083890CUTT	IQXC-26	25.0MHz	20.00pF	±10ppm	±20ppm
LFXTAL052799CUTT	IQXC-26	26.0MHz	10.00pF	±10ppm	±30ppm
LFXTAL066742CUTT	IQXC-26	26.0MHz	8.00pF	±15ppm	±15ppm
LFXTAL066742REEL	IQXC-26	26.0MHz	8.00pF	±15ppm	±15ppm
LFXTAL069296CUTT	IQXC-26	26.0MHz	8.00pF	±15ppm	±20ppm
LFXTAL070729CUTT	IQXC-26	26.0MHz	12.00pF	±10ppm	±15ppm
LFXTAL081614CUTT	IQXC-26	26.0MHz	8.00pF	±10ppm	±20ppm
LFXTAL081614REEL	IQXC-26	26.0MHz	8.00pF	±10ppm	±20ppm
LFXTAL072541CUTT	IQXC-26	27.0MHz	8.00pF	±15ppm	±15ppm
LFXTAL072541REEL	進口晶振	27.0MHz	8.00pF	±15ppm	±15ppm
LFXTAL081610CUTT	IQXC-26	27.0MHz	8.00pF	±10ppm	±20ppm
LFXTAL072302CUTT	IQXC-26	30.0MHz	8.00pF	±15ppm	±15ppm
LFXTAL081612CUTT	IQXC-26	30.0MHz	8.00pF	±10ppm	±20ppm
LFXTAL056523CUTT	IQXC-26	32.0MHz	8.00pF	±20ppm	±20ppm
LFXTAL056523REEL	IQXC-26	32.0MHz	8.00pF	±20ppm	±20ppm
LFXTAL069526CUTT	IQXC-26	32.0MHz	8.00pF	±15ppm	±15ppm
LFXTAL069526REEL	IQXC-26	32.0MHz	8.00pF	±15ppm	±15ppm
LFXTAL079322CUTT	IQXC-26	32.0MHz	12.00pF	±10ppm	±20ppm
LFXTAL079322REEL	IQXC-26	32.0MHz	12.00pF	±10ppm	±20ppm
LFXTAL081613CUTT	IQXC-26	32.0MHz	8.00pF	±10ppm	±20ppm
LFXTAL083149REEL	IQXC-26	32.0MHz	6.00pF	±10ppm	±20ppm
LFXTAL072304CUTT	IQXC-26	37.4MHz	8.00pF	±15ppm	±15ppm
LFXTAL081616CUTT	IQXC-26	37.4MHz	8.00pF	±10ppm	±20ppm

正在載入評論數據...

上一篇：GEYER頻率控制元器件產品

下一篇：QVS新產品QCT95-CU3S-26.000發布會

此文關鍵字：石英貼片晶振

姓名：
郵箱：
正文：

資訊中心

金洛博客

IQD幾皮法會破壞你的計時準確性LFXTAL052799CUTT

相關資訊